<b id="i2rle"><form id="i2rle"></form></b>
    1. <source id="i2rle"><meter id="i2rle"></meter></source> <tt id="i2rle"></tt>

        <b id="i2rle"><tbody id="i2rle"></tbody></b>
        1. 當前位置:首頁-新聞中心>>企業動態>>透明不干膠標簽印刷廠家-不干膠標簽儲存要注意什么?

          透明不干膠標簽印刷廠家-不干膠標簽儲存要注意什么?

          來源:http://www.apersianrug.com/ 日期:2020-12-25 發布人:shengfeng 1. 標簽成品包裝應使用塑料帶包裝密封好,不能直接接觸地面,應置于離地面高度在250px以上的墊塑料板或木板上;未使用完的標簽材料仍使用塑料袋包裝,密閉后放入庫存中,避免標簽吸潮變形;
          1. The packaging of finished label products should be sealed with plastic tape, which can not directly contact the ground, and should be placed on the plastic pad or wood board with a height above 250px from the ground; the unused label materials should still be packed with plastic bags and put into stock after sealing, so as to avoid moisture absorption and deformation of labels;
          2. 環境溫、濕度的平衡對標簽儲存和粘性至關重要,建議儲存環境溫度在20±2℃和65%±5%的相對濕度下可儲存一年。環境溫度應不低于不干膠材料的貼標溫度,一般為+10℃;
          2. The balance of ambient temperature and humidity is very important for label storage and stickiness. It is suggested that the label can be stored for one year at 20 ± 2 ℃ and 65% ± 5% relative humidity. The minimum ambient temperature should not be lower than the minimum labeling temperature of the self-adhesive material, generally + 10 ℃;
          3. 如標簽在冬季儲存溫度低于不干膠貼標溫度,則在使用前48小時,將標簽置于18℃~22℃的環境中,有利于標簽膠水的恢復及貼標
          3. If the storage temperature of the label in winter is lower than the minimum labeling temperature of the self-adhesive, the label should be placed in the environment of 18 ℃ ~ 22 ℃ 48 hours before use, which is conducive to the recovery and labeling of the label glue
          透明不干膠標簽印刷廠家
          4. 成品標簽應避免陽光直接照射,在未使用前保持包裝完整。
          4. The label of finished product should avoid direct sunlight and keep the package intact before use.
          濟南不干膠標簽簽印刷一般要裁切成一定的形狀方能使用,在印刷模切一次成型的印刷機上,模切與印刷的同步至關重要,模切的上下移動和印刷工作臺的上下移動由主傳動軸共同傳動,所以有同步性,但裁切位置,則由雙曲柄結構控制牽引輥轉動的距離來決定,所以調整曲柄半徑大小和壓紙輪壓力非常關鍵
          The printing of label labels in Ji'nan is usually cut into a certain shape and can be used. In the printing and die cutting one forming press, the simultaneous interpreting of die cutting and printing is very important. The up and down movements of the die cutting and the up and down movement of the printing worktable are driven by the main drive shaft, so there is synchronization, but the cutting position is determined by the distance between the two rollers to control the distance of the traction roller. So it is very important to adjust the crank radius and the pressure of the paper roller
          有時不干膠產品上會出現云霧狀的影子,這主要是勻墨不均造成。平壓平不干膠印刷的勻墨輥是一個直徑為150mm可以軸向串動的鍍鉻鐵輥,它的作用是從墨斗輥和傳墨輥上接受油墨并把油墨勻勻調配,再傳送給著墨輥,串墨輥失去串墨作用很容易形成暈影,另外,著墨輥是由軟質的丁腈橡膠硫化制成,如果不注意保養,使著墨效果下降,也會造成暈影,解決暈影就是解決勻墨不均問題,可適當增加給墨量
          Sometimes there will be misty shadow on the self-adhesive products, which is mainly caused by uneven ink. The roller is a 150 mm diameter chromium plated iron roller, which can move in series in axial direction. Its function is to receive ink from the ink bucket roller and the ink transfer roller, and then transfer the ink to the inking roller. If the inking roller loses the inking effect, it is easy to form a halo. In addition, the inking roller is made of soft nitrile rubber vulcanization. If you do not pay attention to maintenance, the inking effect will be improved If the amount of ink drops, it will also cause vignetting. To solve the problem of uneven ink, you can increase the amount of ink
          在有效印刷區域內保持均勻恒定的印刷壓力,不僅能使印刷品墨色均勻,色差小,也能使印跡尺寸穩定,平壓平型印刷機能夠獲得的印刷壓力,但由于它存在的制造精度印版平整度的問題,以及不干膠基材厚薄不可能達到完全均勻,致使壓力不均,影響了印刷質量,解決壓力不均勻的措施一個是做襯墊,哪里壓力小,就把哪里的工作臺下部墊起來;一個是適當降低柔性版的硬度,但降低柔性版的硬度是有限的,如果柔性硬度過低,會使圖文幾何尺寸向外擴張,使細小字體容易模糊。
          Keeping a uniform and constant printing pressure in the effective printing area can not only make the ink color uniform and the color difference small, but also make the imprint size stable. The flat press can obtain the maximum printing pressure. However, due to its manufacturing accuracy, the flatness of the plate and the impossibility of completely uniform thickness of the self-adhesive substrate, the uneven pressure affects the printing Quality, to solve the uneven pressure measures, one is to make a pad, where the pressure is small, put up the lower part of the workbench; one is to appropriately reduce the hardness of the flexo, but reducing the hardness of the flexo is limited, if the flexibility is too low, it will make the geometric size of the text outward expansion, so that small font is easy to blur.
          本文由不干膠防偽標簽印刷整理發布,您是不是對這些內容有所了解了呢?更多的內容請點擊:http://www.apersianrug.com我們會有更多精彩內容等你查看。
          This article is printed and published by the self-adhesive anti-counterfeiting label. Do you know something about it? For more information, please click: http://www.apersianrug.com We'll have a lot more to see.

          上一篇:透明不干膠標簽印刷廠家-常用不干膠標簽表面材料及特點
          下一篇:不干膠標簽印刷時應該注意哪些細節?
          聯系我們
          最新亚洲中文字幕|久久996re热这里只有精品无码|日韩欧美中文字|97久久国产亚洲精品超碰